礦ision Build Log
Project:
E:\Sync_WangXinYue\LCD-200\最终资料\ArduinoSTM32\0164 nt3916 16B 39pin\USER\LCD.uvproj Project File Date: 05/07/2014Output:
Rebuild target 'Target 1' compiling main.c... compiling stm32f10x_it.c... compiling system_stm32f10x.c... compiling led.c... compiling key.c... compiling exti.c... compiling wdg.c... compiling timer.c... compiling pwm.c... compiling lcd.c... compiling delay.c... compiling sys.c... compiling usart.c... compiling core_cm3.c... assembling startup_stm32f10x_md.s... compiling misc.c... compiling stm32f10x_adc.c... compiling stm32f10x_bkp.c... compiling stm32f10x_can.c... compiling stm32f10x_cec.c... compiling stm32f10x_crc.c... compiling stm32f10x_dac.c... compiling stm32f10x_dbgmcu.c... compiling stm32f10x_dma.c... compiling stm32f10x_exti.c... compiling stm32f10x_flash.c... compiling stm32f10x_fsmc.c... compiling stm32f10x_gpio.c... compiling stm32f10x_i2c.c... compiling stm32f10x_iwdg.c... compiling stm32f10x_pwr.c... compiling stm32f10x_rcc.c... compiling stm32f10x_rtc.c... compiling stm32f10x_sdio.c... compiling stm32f10x_spi.c... compiling stm32f10x_tim.c... compiling stm32f10x_usart.c... compiling stm32f10x_wwdg.c... linking... Program Size: Code=11948 RO-data=2928 RW-data=60 ZI-data=1700 FromELF: creating hex file... ".\LCD.axf" - 0 Error(s), 0 Warning(s). Load "E:\\Sync_WangXinYue\\LCD-200\\最终资料\\ArduinoSTM32\\0164 nt3916 16B 39pin\\USER\\LCD.axf" Set JLink Project File to "E:\Sync_WangXinYue\LCD-200\最终资料\ArduinoSTM32\0164 nt3916 16B 39pin\USER\JLinkSettings.ini" * JLink Info: Device "STM32F103VB" selected (128 KB flash, 20 KB RAM). JLink info: ------------ DLL: V4.76d, compiled Sep 13 2013 16:35:06 Firmware: J-Link ARM V8 compiled Jul 17 2013 11:24:15 Hardware: V8.00 S/N : 17935099 Feature(s) : RDI,FlashDL,FlashBP,JFlash * JLink Info: STM32F1xxx: Can not attach to CPU. Trying connect under reset. **JLink Warning: RESET (pin 15) high, but should be low. Please check target hardware. ***JLink Error: Supply voltage too low (1 Volt is required, Measured: 0.0 Volt). Please check target power. Error: Flash Download failed - Target DLL has been cancelled Load "E:\\Sync_WangXinYue\\LCD-200\\最终资料\\ArduinoSTM32\\0164 nt3916 16B 39pin\\USER\\LCD.axf" Set JLink Project File to "E:\Sync_WangXinYue\LCD-200\最终资料\ArduinoSTM32\0164 nt3916 16B 39pin\USER\JLinkSettings.ini" * JLink Info: Device "STM32F103VB" selected (128 KB flash, 20 KB RAM). JLink info: ------------ DLL: V4.76d, compiled Sep 13 2013 16:35:06 Firmware: J-Link ARM V8 compiled Jul 17 2013 11:24:15 Hardware: V8.00 S/N : 17935099 Feature(s) : RDI,FlashDL,FlashBP,JFlash * JLink Info: Found SWD-DP with ID 0x1BA01477 * JLink Info: Found SWD-DP with ID 0x1BA01477 * JLink Info: Found Cortex-M3 r1p1, Little endian. * JLink Info: FPUnit: 6 code (BP) slots and 2 literal slots * JLink Info: TPIU fitted. ROMTableAddr = 0xE00FF003 Target info: ------------ Device: STM32F103VB VTarget = 3.319V State of Pins: TCK: 0, TDI: 1, TDO: 0, TMS: 1, TRES: 1, TRST: 1 Hardware-Breakpoints: 6 Software-Breakpoints: 8192 Watchpoints: 4 JTAG speed: 4000 kHz Erase Done. Programming Done. Verify OK. Application running ...